Quality Used Auto Parts

Used CV Axle for Sale — VIN-Matched OEM Axle Shafts

A clicking noise on tight turns usually means one thing, and it will not fix itself. A used CV axle from Premium Used Auto Parts is sourced from a clean-title U.S. donor vehicle, thoroughly inspected, and VIN-matched to help ensure the correct spline count and vehicle compatibility before shipping. Over 4,500 units are in stock from $75, each covered by a 90-day replacement warranty with no core charge.

  • Fast US Shipping
  • VIN-Verified Spline Count
  • Tested for Popping

Find Your Part

Your information is safe and will never be shared.
1-800-606-1107
We Ship Nationwide
90 Days Warranty
Google Verified
AcuraAlfa RomeoAston MartinAudiBentleyBMWBuickCadillacChevroletChryslerDodgeFerrariFiatFordGenesisGeoGMCHondaHummerHyundaiInfinitiIsuzuJaguarJeepKiaLamborghiniLand RoverLexusLincolnMaseratiMazdaMcLarenMercedes-BenzMercuryMiniMitsubishiNissanOldsmobilePeugeotPlymouthPontiacPorscheRAMSAABSaturnScionSubaruTeslaToyotaVolkswagenVolvo

Complete Your Drivetrain Repair: Shop More Premium Used Auto Parts

Need more than just a used axle? Search thousands of fully tested transmissions, transfer cases, and heavy-duty differentials ready to ship from our US salvage network.

Differential

Differential

Drive Shaft

Drive Shaft

Transfer Case

Transfer Case

Transmission

Transmission

ABS

ABS

What a Used CV Axle Costs by Vehicle Type

Axle shaft price tracks torque capacity, not brand. A shaft that has to survive a three-quarter-ton payload uses more steel and a higher spline count than one turning the front wheel of a compact sedan, and it prices accordingly.

APPLICATIONUSED PRICENEW OEMTYPICAL SAVING
Front CV axle — compact and mid-size sedanMOST COMMON
$75 – $135
$380 – $520
Around 75%
Front CV axle — crossover or SUV, AWD
$110 – $180
$450 – $700
Around 70%
Rear CV assembly — independent rear suspension
$120 – $195
$500 – $780
Around 72%
Solid rear axle shaft — half-ton pickup
$95 – $165
$340 – $560
Around 70%
Full-float shaft — three-quarter and one-ton
$150 – $260
$620 – $900
Around 68%
Half-shaft — EV and hybrid platforms
$180 – $340
$700 – $1,150
Around 65%
Commercial van — fleet and last-mile
$130 – $210
$480 – $740
Around 70%

Three Extra Costs Sit Outside that Table and Catch People Out

Shop labor runs $100 to $200 per side, based on one to two hours. Add an hour if the hub is seized, which is routine on vehicles that have spent winters on salted roads.

A new single-axle axle nut is required on most platforms. Manufacturers do not permit reusing it, and it is a few dollars.

A core deposit applies to nearly every new and remanufactured axle sold elsewhere. We charge none, so nothing is withheld and nothing goes back in a box.

Want the Number for Your Exact Vehicle?

Prices above are typical ranges. Give us your 17-digit VIN and we will quote the exact unit that fits, with the spline count confirmed before you pay.

Call 1-800-606-1107

New, Aftermarket, or Used Which One Actually Makes Sense

There are three ways to replace a failed shaft, and the middle option is the one most people regret.

New OEM from a dealer

Correct, warrantied, and the most expensive route by a wide margin. Often backordered on older platforms.

✓ Pros:

Factory warranty, Exact fit

✕ Cons:

Highest cost, Often backordered

Budget white-box aftermarket

Cheap up front. Widely known in the US repair trade for introducing highway vibration and tearing boots inside a year, at which point you pay the labor twice.

✓ Pros:

Low upfront cost

✕ Cons:

Vibration issues, Boot tears quickly, Pay labor twice

Tested OEM used

Most used axles for sale through our network are the dealer part, pulled from a donor vehicle rather than a factory carton. Same casting, same joint, same spline geometry the manufacturer specified.

✓ Pros:

OEM quality, 50-75% savings, 90-day warranty

✕ Cons:

No factory warranty

What you give up buying used axle shafts is the remaining factory warranty. That is the honest trade. It is also why every second hand axle shaft we ship carries a 90-day replacement warranty of our own.

Six Symptoms That Mean Your Axle Is Failing

Match the noise to the cause before you order. Most people replace a used CV axle after noticing one of these symptoms.

Clicking on tight turns, loudest at low speed

What it usually is: Worn outer CV joint

⚡ Replace now

Vibration that builds with road speed

What it usually is: Bent shaft or failing inner joint

⚡ Within days

Dark grease inside the wheel or on suspension

What it usually is: Torn boot, joint now taking in grit

⚡ Within days

Shudder from a standing start, smooth at cruise

What it usually is: Failing inner tripod joint

⚡ Within weeks

Clunk when shifting between drive and reverse

What it usually is: Excessive spline or joint play

⚡ Within weeks

Uneven tire wear, one side, alignment checks clean

What it usually is: Bent shaft pulling the hub out of true

⚡ Inspect soon

Factory joints typically last 80,000 to 120,000 miles. The joint itself rarely fails first. The boot tears, grease escapes, dirt gets in, and the joint follows shortly after, which is why checking boots at every tire rotation is one of the most cost-effective preventive maintenance steps you can take.

CV Axle or Solid Axle Shaft? Know Before You Order

These two terms get used interchangeably online, and ordering the wrong category is the single most common reason a part comes back to us.

FEATURECV AXLESOLID AXLE SHAFT
Construction
Complete assembly, joints at both ends
Bare splined steel, no joints
Fitted to
Front-drive and independent suspension
Solid rear axles
Typical vehicles
Sedans, crossovers, AWD, most EVs
Trucks, Jeeps, older rear-drive cars
Includes boots and grease
Yes
No
Interchangeable
No – and no adapter exists
No

If you are unsure which one is under your vehicle, look at the wheel end. A CV axle has a rubber boot clamped over each joint. A solid shaft has a bare flange bolted to the hub.

Why the Left and Right Sides are Not the Same Part

Left and right units are almost never identical, and assuming they are is an expensive afternoon.

On transverse-engine front-drive cars, the two shafts differ in length because the transmission does not sit centered in the bay.
The longer side often runs an intermediate shaft or a carrier bearing the short side does not have at all.
Some platforms use different inner spline counts from one side to the other, on the same car, in the same model year.
On solid-axle trucks, rear shafts are side-specific too, because the differential sits off-center in the housing.
On crossovers with independent rear suspension, the rear units are CV assemblies and follow the same rules as the front.

Give us the position in plain terms — front or rear, driver or passenger — and we map it to the correct OEM number.

The Seven Checks Every Shaft Passes Before It Ships

This is where we differ from a self-service yard, where you buy whatever is still bolted to the donor car.

Joint articulation: Every joint is worked by hand to check for binding, notchiness, or play.
Boot inspection: Tears, cracks, hardening, and clamp condition, on both ends.
Straightness check: So you are not chasing a highway vibration after installation.
Spline verification: Inner and outer counts verified using the OEM part number.
ABS tone ring match: Ring type and tooth count checked. Fit the wrong ring and you install a mechanically perfect part and set a fault code the moment you drive it.
Documentation: Donor mileage and title status recorded against the unit, so you know what you are buying.
Donor screening: Vehicles with side-impact or suspension damage are rejected outright, because a curb strike bends a shaft without leaving a visible mark.

Not Sure Which Side or Spline Count You Need?

Share the details of the old part with us and our teardown team will identify it, usually the same business day. No obligation, no pressure.

Get Your Free Fitment Check

Which Makes and Models We Stock Most

Toyota is our highest-volume platform by a clear margin.

Toyota and Lexus

Camry, Corolla, RAV4, Highlander, Tacoma, Tundra, and the Lexus equivalents.

Nissan, Honda, Mitsubishi, Mazda

Deep coverage across sedans and crossovers, front and rear.

Domestic trucks

Full-float and semi-float shafts for half-ton through one-ton pickups, plus complete rear assemblies with verified gear ratios.

Jeep and off-road

Front and rear shafts for solid-axle platforms, checked for yoke integrity and spline wear.

Commercial and fleet vans

A used truck axle or van shaft rated and inspected for load service.

Fleet and last-mile delivery vans wear these parts faster than anything else on the road. Constant low-speed turning, frequent stops, and heavy payloads are close to a worst-case duty cycle for a constant-velocity joint, and van operators replace them at two to three times the rate of a private car. We keep used Toyota axle shafts and domestic van stock deep for that reason.

What EV Owners Need to Know About Half-Shafts

Electric motors make peak torque from zero rpm, so the joints on an EV see load spikes a comparable gasoline car never produces.

  • Mileage matters more. Clicking shows up earlier in an EV's life. Under 80,000 miles on the donor is a sensible target.
  • Front and rear do not interchange on all-wheel-drive platforms, and part numbers can differ between trim levels within one model year.
  • Verify against the number stamped on your original part, not the year and model.
  • The axle nut is single-use with a high torque figure. Clean the splines, use a molybdenum-based grease, and torque to the factory specification.

Skipping that last step is the most common reason a correctly ordered replacement starts clicking within a week.

Tools You Need Before You Lift the Car

Before you begin, make sure you have all the required tools ready. Proper preparation helps prevent unnecessary delays and ensures a smoother, more efficient installation process.

Breaker bar and torque wrench

Ratchet and socket set

Pry bar or a dedicated axle puller

Dead-blow hammer

Jack, Hydraulic floor jack, and wheel chocks

Drain pan and safety glasses

A new single-use axle nut, ordered with the shaft

Axle nut socket in the correct size for your platform

How Long a Used Axle Lasts and What Shortens It

A tested OEM unit with intact boots and tight joints typically runs 60,000 to 100,000 miles — close to whatever remains of the factory part's service life. Three things cut that short, and all three are avoidable.

  • A torn boot left unrepaired. Replace it within a few hundred miles and the joint underneath usually survives.
  • Aggressive off-road use, which loads the joint at angles it was not designed to hold under power.
  • Lifted suspension without correction, which forces the joint to operate at a permanently steeper angle.

Three Things to Have Ready When You Call

Your 17-digit VIN. It is the only reliable way to confirm spline count, transmission code, and ABS configuration. Year, make, and model alone are not enough.
The position. Front or rear, driver or passenger side.
Whether you need a complete assembly or a bare shaft.

We cross-reference OEM part numbers while you are on the line, then ship to your home address or straight to your repair shop.

Why Buyers Come Back to Premium Used Auto Parts

We are a US salvage supplier based in Rancho Cordova, California, shipping to all USA continental states.

Genuine OEM only. No white-box aftermarket, ever.

VIN-matched fitment confirmed before you pay, not after it arrives.

Zero core charge on every unit.

90-day replacement warranty.

Specialists who have handled the part, not read from a script.

A search for a used CV axle near me reaches our full national network rather than one local yard. See our warranty page for full coverage terms, or read our shipping policy for delivery timelines.

Customer Stories

Real Stories from Our Used Axle Shaft Buyers

Discover why US auto shops and DIY mechanics trust our tested and certified used cv axles.

Every review is from a verified buyer who saved hundreds on their exact-fit used axle shafts without paying a single core charge.
❝
5/5

Ordered heavy-duty axle shafts for our F-350 fleet. Each shaft came spline-checked, balanced, and straightness-tested. Zero vibration issues and perfect fitment. Their quality control process is outstanding for fleet applications.

P
Pablo Dominguez
Verified Purchase
❝
5/5

Incredible experience sourcing a BMW engine. When original unit sold, they quickly found a perfect replacement. Outstanding communication kept both me and my mechanic updated on status. Their expertise in luxury vehicle engines and attention to detail made the whole process seamless.

D
Devyn Clay
Verified Purchase
❝
5/5

The support team's knowledge and patience in answering all engine-related questions was impressive. Their thorough technical expertise and detailed explanation of the testing process gave complete confidence in my purchase. Premium quality backed by exceptional service.

E
Elizabeth Barely
Verified Purchase
❝
5/5

Quick and professional response regarding a Chevy Equinox engine. The team provided comprehensive cost estimates, including testing documentation and warranty details. Their transparent pricing and technical verification process made decision-making easy. Outstanding service!

C
Cameron
Verified Purchase
❝
4/5

From initial engine sourcing to post-delivery support, the team demonstrated exceptional service. When an issue arose, they resolved it immediately. Their commitment to customer satisfaction and quality assurance is remarkable. Definitely the go-to source for premium used engines!

T
Tamara V
Verified Purchase
❝
5/5

Ordered heavy-duty axle shafts for our F-350 fleet. Each shaft came spline-checked, balanced, and straightness-tested. Zero vibration issues and perfect fitment. Their quality control process is outstanding for fleet applications.

P
Pablo Dominguez
Verified Purchase
❝
5/5

Incredible experience sourcing a BMW engine. When original unit sold, they quickly found a perfect replacement. Outstanding communication kept both me and my mechanic updated on status. Their expertise in luxury vehicle engines and attention to detail made the whole process seamless.

D
Devyn Clay
Verified Purchase
❝
5/5

The support team's knowledge and patience in answering all engine-related questions was impressive. Their thorough technical expertise and detailed explanation of the testing process gave complete confidence in my purchase. Premium quality backed by exceptional service.

E
Elizabeth Barely
Verified Purchase
❝
5/5

Quick and professional response regarding a Chevy Equinox engine. The team provided comprehensive cost estimates, including testing documentation and warranty details. Their transparent pricing and technical verification process made decision-making easy. Outstanding service!

C
Cameron
Verified Purchase
❝
4/5

From initial engine sourcing to post-delivery support, the team demonstrated exceptional service. When an issue arose, they resolved it immediately. Their commitment to customer satisfaction and quality assurance is remarkable. Definitely the go-to source for premium used engines!

T
Tamara V
Verified Purchase
Got Questions?

Complete Guide: Used CV Axle FAQs

Get clear answers before you order your replacement. Learn how to choose the right OEM-used CV axle, verify VIN compatibility, understand pricing and warranties, and avoid common fitment mistakes.


Call with your VIN and we will confirm fitment in minutes, quote the exact part, and get it moving the same business day. No core charge, 90-day warranty.

Call Now 1-800-606-1107
Auto parts warehouse
Call Us Now1-800-606-1107